Toupret Decorators Quick Dry Filler TX 110 5kg 5 x 1kg TTREB9051GB

Toupret Decorators Quick Dry Filler TX 110 5kg 5 x 1kg TTREB9051GB

MPN: TTREB9051GB

Barcode: 3178310018620

Size: 5kg (5 x 1kg bags)

Colour: White (when dry)

Overview:

The Toupret Quick Dry Filler TX 110 is a professional powder filler for fast interior wall and ceiling repairs. It dries ready to paint in just 3 hours and will not shrink or slump, even when applied at depth. No spot priming is required after application.

This filler bonds strongly to a wide range of interior substrates, from gypsum plaster and plasterboard to cement, brick, and primed wood. It sands back with ease and will not flash or grin under paint. A working time of 30 to 40 minutes gives good control during application.

The TX 110 holds an A+ Indoor Air Quality (IAQ) classification, making it well-suited to occupied spaces. It accepts any paint, filler, or wall coating once dry. Each 5kg pack contains five individual 1kg bags for easy portioning on site.

Key Features and Benefits

• Fast overcoating: Ready to paint or wallpaper in just 3 hours under normal conditions.
• No shrinkage or slumping: Holds its shape at any fill depth, with no depth limitation.
• No spot priming required: Will not flash or grin under paint, even on high-sheen finishes.
• Strong adhesion: Tested to greater than 0.5 MPa (per EN 16-566) across a wide range of interior substrates.
• Easy sanding: Cuts back smoothly for a clean, flat finish with minimal effort.
• 30 to 40 minute working time: Allows adequate time to shape and smooth repairs before the material sets.
• A+ IAQ classification: Achieves the highest Indoor Air Quality standard, making it safe for use in occupied areas.
• Broad overcoating compatibility: Accepts any conventional paint, specialist coating, or additional filler once dry.
• Wide substrate range: Bonds to new and old surfaces, including plasterboard, concrete, breeze block, brick, stone, and primed wood.
• White finish when dry: Makes it easy to check coverage before painting.
• Water-based formula: Tools clean up with water, with no solvents required.
• Convenient pack format: Supplied as five individual 1kg bags within a single 5kg outer bag for easy portioning.

Typical Applications

• Wall repairs: Filling cracks, holes, and surface damage on gypsum plaster and plasterboard walls.
• Ceiling repairs: Patching damaged or cracked interior ceilings before decoration.
• Pre-decoration preparation: Smoothing imperfections on old painted surfaces before repainting or wallpapering.
• Concrete and masonry repairs: Filling surface defects in cement, concrete, cellular concrete, and breeze block walls.
• Brickwork and stone: Patching localised surface damage on brick and stone interior walls.
• Primed wood: Filling minor imperfections on primed timber surfaces before top-coating.
• Fast-turnaround projects: Any interior decoration work where overcoating on the same day is required.

How to Use

• Surface preparation: Make sure the substrate is clean, sound, and free from dust, grease, and any loose material. Do not apply below +8°C or above +35°C, or when relative humidity exceeds 70%.

• Mixing: Add 450ml of water per 1kg of powder (a 45% ratio). Pour the powder into the water at room temperature, then stir until the mix is smooth and lump-free.

• Application: Apply with a putty knife, taping knife, or trowel. Build up to the required depth in a single pass - there is no maximum fill depth. Work the material to a smooth finish.

• Drying time: Leave the filler to dry for a minimum of 3 hours before overcoating. Actual drying time will vary depending on coat thickness, substrate type, and ambient conditions.

• Sanding: Once fully dry, sand back the repair with a fine-grit abrasive to achieve a smooth, flat surface flush with the surrounding area.

• Overcoating: Apply any conventional paint, wall coating, or wallpaper directly over the repair. No spot priming is needed before painting.

Frequently Asked Questions (FAQs)

• How long does Toupret Quick Dry Powder Filler TX 110 take to dry before painting?
  The filler is ready to paint in 3 hours in standard conditions. Drying time may be longer with thicker applications, in cold temperatures, or at high humidity levels.

• Can Toupret Quick Dry Filler be used on exterior surfaces?
  No. The TX 110 is formulated strictly for interior use. Do not apply it to exterior walls or surfaces exposed to weather or moisture.

• Do I need to prime over Quick Dry Filler before painting?
  No spot priming is required. The filler will not flash or grin under paint, including finishes with a high sheen level, provided it is completely dry before overcoating.

• What is the maximum fill depth for Toupret Quick Dry Filler TX 110?
  There is no maximum fill depth. The product can be applied at any thickness in a single pass without shrinking or slumping.

• How do I mix Toupret Quick Dry Filler TX 110 Powder Filler?
  Add 450ml of clean water per 1kg of powder. Pour the powder into the water - not the other way round - and stir thoroughly until the mix is smooth. The working time after mixing is 30 to 40 minutes.

Summary

The Toupret Quick Dry Filler TX 110 5kg delivers fast, professional-quality interior repairs with a 3-hour overcoat time and no need for spot priming. It bonds to a broad range of interior substrates, holds its shape at any fill depth, and sands back cleanly. The five-bag format makes it a useful option for decorators working across multiple areas or sites.

"Always read the Toupret Quick Dry Powder Filler TX 110 Technical Datasheet before first use to make sure that you have the correct information and product for your application."