Bond It Exterior Render Pregrit External 10L Bonding Agent Coating BDEPG10

Bond It Builder Complete Render Pregrit External Rendering Bonding Agent Paint Exterior Coating 10L

Tub Size: 10 Litre

MPN: BDEPG10

Barcode: 5060021361073

Product Overview:

Bond-It Exterior Render PREGRIT External bonding agent is a one part Exterior pre grit GRIPCOAT paint on coating the green colour of the grip coat shows uniformity of the coating. Bond it render pregrit designed to work externally a  paint on ready-to-use Internal and external render bonding agent with added aggregate that provides a key grip prior to rendering, used as an effective bonding agent for render to concrete, brickwork and blockwork, and as a bonding agent to improve adhesion to smooth surfaces, pre grit can be applied by brush or roller.

Bond it Exterior Pregrit from the Builders Complete professional range of building chemicals it can be used as a bonding agent for block brick and non similar surface including smooth surfaces, it contains a special sand aggregate to provide plaster render permanent grip, the coating is ready to use and only needs one coat - application this saves on money and time perfect for use on smooth substrates, pigmented light green to make identify treated areas easy.

Pre Grit Uses:

Render PREGRIT should be used as a primer and bonding aid prior to rendering on surfaces such as concrete, brick and difficult, low or non-porous substrates for internal and external use 

Can also be used on external wall areas that will have a tiled finish.

Bond It Builders Complete Pregrit Benefits and Areas of Use:

• Size: 10 Litre
• Grade: Waterproof bonding agent for exterior walls.
• For use on: concrete, brickwork, light blockwork.
  
• Economical in use: Single one coat application that is then rendered once cured.
• Type: Exterior Render PREGRIT External bonding agent.
• Porosity: Reduces suction on porous surfaces and improves adhesion, helps to prevent cracking in the render from over porous surfaces.
• Surfaces: used as an effective bonding agent for render to concrete, brickwork and blockwork and non similar surface including smooth surfaces.
• Identification:  The green colour shows uniformity in the coating unlike clear coatings.
• Areas: Can be used Internally and Externally.

How to Apply External Pregrit:

• Thoroughly stir before use and ensure application temperature is above +5 degree C and that the surface to be treated is free from dust, release agents and any contaminants that may hinder adhesion.
• Any contamination must be removed prior to application, including any flaking material ensuring the background is sound and will support the weight of the render.
• Do not dilute Bond-It render pre grit it is recommend a patch test be carried out on a small inconspicuous area to test compatibility prior to full application.
• Simply apply 1 coat using a brush or roller ensuring an even coat and allow to dry 6 hours minimum.
• This product is coloured light green to identify treated areas and uniformity of the coating.
• Protect adjacent surfaces from splashes and remove any EXTERIOR PREGRIT before drying using warm soapy water as later it will not come off.

Important Product Note:

• Cold or humid conditions will increase drying times.
• Do not use at temperatures below +5 degree C.
• Cold or humid conditions will increase drying times.
  

Product Limitations:

• Do not use on areas subject to continual damp this is not a DPM.
• Do not dilute.
• Do not exceed a maximum thickness of 25mm for complete render system.
• Remove any contamination of product to surrounding surfaces before drying.

Approximate Coverage:

• Depending upon surface porosity and texture 10 litre will cover approximately 30 meters square.

Also Available Internal Plaster Pregrit

FAQS:

1. What is Bond It Pre-Grit Bonding Agent used for?
Bond It Pre-Grit is a high-performance bonding primer designed to improve the adhesion of cement-based render systems to smooth, low-suction or non-porous surfaces such as concrete, plaster, and painted walls.

2. Can this bonding agent be applied to painted surfaces?
Yes, it is specifically formulated to bond to previously painted surfaces, providing a textured key for new render or plaster to grip onto securely.

3. How should I apply Bond It Pre-Grit?
Apply using a brush or roller in a single even coat. Stir thoroughly before use. Allow it to dry fully 6 hours minimum before rendering over depending on conditions.

4. Is the Bond It Pre-Grit suitable for exterior use?
Absolutely. It is engineered for external use and can withstand outdoor exposure, making it ideal for render preparation on exterior walls.

5. What surfaces are compatible with this bonding primer?
It adheres to smooth concrete, plaster, existing render, blockwork, painted surfaces, dense brickwork, and other low suction substrates.

6. How much coverage does the 10-litre tub provide?
A 10-litre tub typically covers approximately 30–50m² depending on surface porosity and application thickness.

7. Does Bond It contain any grit or aggregate?
Yes, it includes a fine aggregate (grit) which helps create a mechanical key for improved render adhesion on smooth or difficult surfaces.

8. Can it be used on internal walls as well?
While primarily intended for external use, it can also be applied to interior surfaces where extra bonding strength is required before plastering.

9. Is it ready to use straight from the tub or does it require mixing?
It is supplied ready to use — no mixing required. Just stir thoroughly before application to ensure even distribution of grit and primer.