Toupret Plasterboard Joint & Skim Ready to Use 10kg Tub FGBJP10GB

Toupret Plasterboard Joint & Skim Ready to Use 10kg Tub FGBJP10GB

MPN: FGBJP10GB

Barcode: 3178310019221

Weight: 10kg

Overview:

Toupret Plasterboard Joint & Skim Ready to Use is a pre-mixed interior filler for plasterboard jointing and surface finishing. It applies straight from the tub with no mixing required. The formula delivers a smooth, consistent result with minimal shrinkage across a wide range of interior substrates.

Compatible with both manual and airless spray application, this filler works on plasterboard, gypsum, cement, concrete, cellular concrete, old painted surfaces, and primed wood. Coverage is 1.7kg per m² at 1mm depth. It can be applied up to 5mm thick in a single pass.

The product conforms to BS EN 13963:2014 for jointing applications and holds an IAQ A+ indoor air quality classification. It carries a 12-month guarantee from the date of purchase when stored correctly in its original, sealed packaging.

Key Features and Benefits

• Ready to Use: No mixing required - apply straight from the tub.
• BS EN 13963:2014 Compliant: Meets the standard for jointing materials for gypsum boards.
• IAQ A+ Rated: Very low VOC emissions at under 0.001%, suitable for occupied interior spaces.
• No Spot Priming Needed: Apply directly to the substrate without priming first.
• Maximum 5mm Application Thickness: Allows for a range of jointing and finishing depths in one pass.
• Unlimited Working Time: No time pressure during application - work at your own pace.
• Easy to Sand: Sands back smoothly once fully dry for a clean finish.
• Manual or Spray Application: Works by hand with a blade or trowel, or via airless spray machine.
• Fast Return to Service: Ready to overcoat in 12-24 hours under average conditions.
• Strong Adhesion: Achieves an adhesion strength of over 0.5 MPa per EN 16566.
• 12-Month Guarantee: Backed by a product guarantee from the date of purchase.
• White When Dry: Provides a clean, neutral base for painting or wall coating.

Typical Applications

• Plasterboard Jointing: Filling and finishing joints on plasterboard in new builds and refurbishments.
• Surface Skimming: Producing a smooth, flat finish over plasterboard and gypsum.
• Cement and Concrete Walls: Finishing interior cement, concrete, and cellular concrete surfaces.
• Old Painted Surfaces: Applying over previously painted interior walls that are sound and dry.
• Machine-Applied Finishing: Airless spray application for large surface areas or high-volume work.
• Primed Wood: Finishing over primed wood in interior settings.
• Pre-Paint Preparation: Building a smooth, paintable surface prior to decoration.

How to Use

• Preparation: Check the substrate is clean, dry, hard, and cohesive before starting work. Prepare surfaces in line with current trade practices.

• Condition Check: Do not apply below +8°C or above +35°C. Do not apply where relative humidity exceeds 70%.

• Application: Apply by filling knife, trowel, or coating blade. For machine use, set the airless spray to a flow rate of 5 litres per minute.

• Thickness: Apply up to a maximum of 5mm. For standard jointing and skimming, a typical thickness of 0.5mm is recommended.

• Drying: Allow each coat to dry fully to the touch before applying the next. In average conditions, the surface is ready to overcoat in 12-24 hours.

• Sanding and Finishing: Sand lightly once dry. Always wear a P2 dust mask when sanding. Overcoat with any compatible paint, filler, or wall coating.

Frequently Asked Questions (FAQs)

• What surfaces can this plasterboard jointing filler be applied to?
  It adheres to plasterboard, gypsum, cement, concrete, cellular concrete, old painted surfaces, and primed wood. It is for interior use only and must not be applied to exterior surfaces.

• How long does this filler take to dry before painting?
  In average conditions, the surface is ready to paint in 12-24 hours. Actual drying times vary depending on substrate type, coat thickness, temperature, and humidity.

• Does the surface need to be primed before application?
  No. There is no requirement to spot prime before applying this filler. It can go directly onto compatible substrates without a primer coat.

• What is the maximum thickness that can be applied in a single coat?
  The product can be applied up to 5mm thick. For jointing and skimming, a standard application thickness of around 0.5mm is typical.

• Can this filler be used with a spray machine?
  Yes. It is compatible with airless spray machines set to a flow rate of 5 litres per minute. It can also be applied by hand using a blade, trowel, or filling knife.

Summary

Toupret Joint & Skim Ready to Use is a professional pre-mixed filler for interior plasterboard jointing and surface finishing, supplied in a convenient 10kg tub. It conforms to BS EN 13963:2014, holds an IAQ A+ rating, and is backed by a 12-month guarantee. With unlimited working time, no mixing, and no spot priming required, it is a straightforward choice for tradespeople working across a broad range of interior substrates.

"Always read the Toupret Plasterboard Joint & Skim Ready to Use Technical Datasheet prior to first use to make sure that you have the correct information and product for your application."