Toupret Decorators Patch & Repair Filler Quick Dry 1kg FGREB01GB

Toupret Decorators Patch & Repair Filler Quick Dry 1kg

MPN: FGREB01GB

Barcode: 3178310017920

Colour: White (when dry)

Weight: 1kg

Overview:

Toupret Decorators Patch & Repair Filler Quick Dry is a powder-form interior repair filler for gaps, cracks, scratches, and holes. It is ready to paint in just 3 hours, with no shrinkage and no depth limit. The formula has a VOC content below 0.1% and meets BS EN 16566:2014.

Apply in one coat with no need for spot priming before painting. Adhesion to substrate exceeds 0.5MPa when tested per EN 16566. The filler bonds to plasterboard, gypsum plaster, cement, concrete, cellular concrete, breeze blocks, bricks, stone, and primed wood.

A 12-month guarantee applies from the date of purchase, provided the powder is stored in its original sealed packaging away from moisture. Do not apply below 8°C or above 35°C, or in conditions above 70% relative humidity.

Key Features and Benefits

• Ready to paint in 3 hours: Cuts waiting time on repair and redecoration projects, subject to ambient conditions.
• One coat application: A single pass is sufficient for most repairs, saving time and material.
• Easy to sand: Sands back smoothly for a flat, paint-ready finish.
• No shrinkage: The filler holds its volume as it sets, avoiding recessed or sunken repairs.
• No depth limit: Deep holes and gouges can be filled in a single application pass.
• No spot priming required: Paint or wall coating can go straight on once the filler is dry.
• 40-minute working time: Provides enough time to apply and finish the filler before it begins to set.
• Powder form with known yield: Mix only what you need - 1kg fills 1 litre at the recommended 45% mixing ratio.
• Strong adhesion: Exceeds 0.5MPa adhesion to substrate per EN 16566 testing.
• BS EN 16566:2014 compliant: Classified NFT 36 005 Family III Class 3 for interior fillers.
• Low VOC: VOC content below 0.1%, reducing volatile emissions into indoor spaces.
• 12-month guarantee: Covered from purchase when stored correctly in its original sealed packaging.

Typical Applications

• Filling cracks and holes in plasterboard partitions and ceilings
• Repairing gaps and scratches in gypsum plaster walls
• Patching damage to old painted interior surfaces before redecoration
• Filling voids in cement, concrete, or cellular concrete substrates
• Repairing surface defects in breeze blocks, brick, and stone interior walls
• Patching holes and scratches on primed wood interior surfaces
• Pre-paint preparation over any filler in the Toupret product range

How to Use

• Preparation: Check the substrate is hard, clean, dry, and free of loose material. Remove any unstable areas before applying.

• Mixing: Add 450ml of water per 1kg of powder (45%). Pour the powder into water at room temperature. Stir until smooth and lump-free. Working time once mixed is 40 minutes.

• Application: Apply the mixed filler using a filling knife, trowel, or coating blade. There is no fill depth limit, so holes of any depth can be filled in a single pass.

• Setting: Allow at least 45 minutes before applying a second coat if needed. Times depend on substrate type, coat thickness, and conditions.

• Sanding: Once fully dry, sand the surface smooth. Wear a P2 dust mask and protective goggles when sanding.

• Overcoating: Apply paint, filler, or wall coating after approximately 3 hours of average drying time. Actual times vary by conditions.

Frequently Asked Questions (FAQs)

• How long does Toupret Patch & Repair Filler Quick Dry take before you can paint over it?
  Under average conditions (20°C, 50% relative humidity), the filler is ready to paint in approximately 3 hours. Thicker coats or higher humidity will extend this drying time.

• Can this filler be used on exterior surfaces?
  No. This product is for interior use only and must not be applied to external surfaces.

• Does Toupret Patch & Repair Filler Quick Dry need a primer before painting?
  No spot priming is required. Once fully dry, paint or wall coating can be applied directly to the filled area.

• What is the mixing ratio for Toupret Patch & Repair Filler Quick Dry?
  Add 450ml of water per 1kg of powder (a 45% ratio). Pour the powder into the water and stir until smooth. 1kg of powder yields approximately 1 litre of mixed filler.

• What surfaces can Toupret Patch & Repair Filler Quick Dry be applied to?
  It works on gypsum plaster, plasterboard, old painted surfaces, cement, concrete, cellular concrete, breeze blocks, bricks, stone, and primed wood - provided all substrates are interior.

Summary

Toupret Patch & Repair Filler Quick Dry 1kg is a powder-form interior filler that handles gaps, cracks, scratches, and holes across a wide range of substrates. It applies in one coat with no depth limit, requires no spot priming, and is ready to paint in just 3 hours. The product is BS EN 16566:2014 compliant and backed by a 12-month guarantee.

"Always read the Toupret Decorators Patch & Repair Filler Quick Dry Powder Technical Datasheet prior to first use to make sure that you have the correct information and product for your application."