Everbuild TileSet 700 Universal Int Ext Floor Wall Tile Adhesive Grey 20kg TS700GY20

Everbuild TileSet 700 Universal Internal External Floor Wall Tile Adhesive Grey 20kg

Sika Code 678329

MPN TS700GY20

Barcode 5029347615819

Everbuild Tileset 700 universal standard set internal external powdered floor and wall tile adhesive grey a 20kg bag is a cement-based modified powdered tile adhesive with standard setting properties.

Tile Set 700 grey has extended open time and is designed for applications where extensive cutting is required during application.

Suitable for fixing most substrates including ceramic, natural stone, concrete, unskimmed plasterboard, dense block work, cement screeds and cement based tile backer boards.

Everbuild 700 Tileset grey wall and floor adhesive is water resistant and is suitable for tiling domestic communal and power showers it also has excellent adhesion properties.

Everbuild 700 grey Tile Set is a standard setting ceramic tile adhesive has a setting time of 24 hours. The adhesive is water-resistant and can be used in areas such as bathrooms, kitchens, showers, remains workable for 4 to 5 hours depending on absorbency of the substrate and temperature.

Everbuild TileSet 700 Benefits and Areas of Use:

• Long setting time for areas needing more tile cutting.
• GREY in colour.
• Excellent adhesion properties.
• Excellent non slipping properties.
  
• Can be used Internally and externally.
• Frost Resistant.
  
• Thick or thin bed adhesive from 3mm up to 10mm.
  
• Tiles can be grouted approximately 24 hours after fixing.
  
• Approximate coverage 4kg per square meter.
• Open time 4 to 5 hours.
  
• Water resistant, recommended for tiling domestic communal and power showers
• High bond strength.
• For securing floor and wall tiles to most surfaces.
• Can be used in heavy duty areas such as heavily walked floors.
• May also be used for patching small areas in concrete and stone etc.
• Suitable for fixing most substates including Non Skimmed plasterboard, ceramic, porcelain, natural stone, concrete, Cement based tile backer boards.
  

Everbuild 700 Tileset Grey Universal Standard setting Time Instructions:

Plasterboard:

• Porous substrates like non skimmed plasterboard must be primed with Everbuild SBR Bond diluted 3 to 1.
  

Concrete Screeds Renders:

• Allow fresh concrete etc to dry for at least 4 weeks before tiling.
• Prime surfaces with Everbuild SBR Bond diluted 3 parts water to 1 part SBR+ and allow to dry.
• Surfaces such as tamp rutted concrete and masonry blockwork, that are rough or uneven, should be prepared with a suitable Sikafloor Self Levelling compound and allowed to fully cure for at least 24 to 48 hours before application.
  

Existing Tilled Surfaces:

• Ensure tiles are securely bonded to wall or floor.
• Roughen surface of glazed tiles with sander.
• Apply a bonding coat of neat Everbuild SBR Bond or Adhesion modifiers coatings.
• Apply mixed adhesive whilst bonding coat is still tacky.
  

Mixing:

• Everbuild 700 should be added to clean water in a mixing bucket and mixed with a paddle mixer if available.
• The sides of the bucket can be brought into the mix by using a bucket trowel to prevent any dry lumps in the mixed tile adhesive.
  
• Mix approximately 3 parts by volume powder to 1 part by volume water.
  
• Always add powder to water.
  

Application:

1. Using a large notched trowel spread the adhesive evenly onto the substrate the Size of notches depends on size of tiles being used, the surface being tiled, the profile on back of the tiles, and degree of coverage required.
2. Press the tiles firmly into place using a slight twisting action.
3. Leave a grout joint this can be done using tile spacers unless self spacing tiles are used.
4. Surface adhesive should be cleaned from the faces of the tiles with a moist cloth or sponge.
   
5. Rake out excessive adhesive from within joints before setting takes place.
6. The open time of the exposed adhesive bed is approximately 4 to 5 hours depending on surface porosity and site conditions.
7. Grouting may proceed as soon as the tile bed is sufficiently firm, which will be around 24 hours at room temperature.
   
8. Do not use at temperatures below +5 deg C or above 35 deg.
   

Grouting:

1. Allow 24 hours before grouting depending on site conditions or when tiles are sufficiently firm to accept light foot traffic.
2. Follow the manufacturer’s instructions for protecting and sealing the tiles before and after grouting.
   

Always Read the Official Technical Data sheet prior to use to make sure you have all the details are correct and that there have not been any changes to instructions.

Also Available Everbuild 700 Tile Set Tile Adhesive in White for those light coloured tiles

Everbuild 700 Tileset TS700GY20 vOfficial Information:

Everbuild 700 Universal Tileset Standard Set Tile Adhesive Technical Data Sheet

Everbuild 700 Universal Tileset Tile Adhesive  Safety Data Sheet

Everbuild Tile Set 700 Manufacturer Product Page