Tolsen Paint Mixer 400mm x 80mm Hex Shaft 40098

Tolsen Paint Mixer 400mm x 80mm Hex Shaft

MPN: 40098

Barcode: 6933528740339

Size: 400x80x8mm

Weight: 213g

Overview:

The Tolsen Paint Mixer is a drill-powered mixing attachment made from special tool steel with a powder-coated finish. It fits standard drill chucks and reaches the bottom of most paint cans without difficulty.

The 80mm mixing head blends paints, primers, stains, and thin compounds to a smooth texture. At 400mm in length, it handles containers from standard 1-litre tins to larger 5-litre buckets. A rubber hanging hole keeps the mixer on a hook between uses, so it is always available when you need it. At 213g, it is light enough to hold comfortably throughout longer mixing sessions.

Key Features and Benefits

• Special Tool Steel Construction: Made from tool steel for lasting strength and consistent mixing performance over time.
• Powder-Coated Finish: The smooth coating resists rust and wipes clean quickly after use.
• 400mm Length: Reaches the bottom of standard paint cans and buckets without fully submerging the drill.
• 80mm Mixing Head: Thoroughly blends paint, primer, stain, and thin plaster compounds to a uniform texture.
• 8mm Hex Shank: Fits securely into most standard 10mm and 13mm drill chucks.
• Rubber Hanging Hole: Store the mixer on a hook to keep your work area tidy between jobs.
• Lightweight at 213g: Reduces hand and wrist tension during extended mixing sessions.
• Compatible with Most Drills: Works with the majority of corded and cordless electric drills available.
• Wide Material Range: Handles paint, primer, stain, sealer, and thin plaster - not just standard wall paint.
• Faster Than Hand Stirring: Achieves a thorough, consistent mix in a fraction of the time taken by hand.

Specs & Attributes

• Size: 400x80x8mm
• Length: 400mm
• Width: 80mm
• Shaft Diameter: 8mm
• Weight: 213g
• Material: Special Tool Steel
• Finish: Powder Coated

Typical Applications

• Mixing wall and ceiling paint before application
• Blending primers and undercoats to a consistent colour
• Stirring wood stains and treatments
• Mixing sealers and surface treatments
• Combining thin plaster and drywall compounds
• Blending pigments and tinters into base paint
• Re-mixing settled or separated paint that has been stored

How to Use

• Attach to your drill: Insert the 8mm hex shank into the drill chuck and tighten it firmly before use.

• Submerge the head: Lower the mixing head fully into the paint or compound before you start the drill.

• Start at low speed: Begin at the lowest speed setting to prevent splashing, then increase gradually as the material begins to move.

• Work the mixer: Move the head up and down and around the container to lift settled pigments from the bottom.

• Mix for 2-3 minutes: Continue until the colour and texture are uniform throughout - even if it looks blended, keep going to be thorough.

• Clean promptly: Wipe or rinse the head while the material is still wet to protect the powder-coated finish and make cleanup straightforward.

Frequently Asked Questions (FAQs)

• What drill speed should I use with a paint mixer?
  Start at the lowest speed setting on your drill. This prevents paint from splashing out of the can. Once the material starts moving freely, increase the speed gradually to complete the mix.

• Will this mixer fit my drill chuck?
  The 8mm hex shank fits most standard 10mm and 13mm drill chucks found on common corded and cordless drills. Tighten the chuck firmly before starting.

• Can this mixer be used with an impact driver?
  A standard electric drill is recommended for mixing attachments. Impact drivers deliver rotational force in a different way and are not well-suited to paint mixing tasks.

• How do I clean the mixer after use?
  Wipe the head with a cloth while the material is still wet. For water-based products, rinse under running water. For solvent-based products, clean with the appropriate solvent before the material cures.

• Is this mixer suitable for thick materials like tile adhesive or cement?
  This mixer suits thin-to-medium consistency materials - paint, primer, stain, sealer, and thin plaster compounds. For thick or heavy materials such as cement or tile adhesive, a heavy-duty paddle mixer is more appropriate.

Summary

The Tolsen Paint Mixer 400x80x8mm is a drill-mounted mixing attachment made from special tool steel with a protective powder-coated finish. It suits a wide range of liquid and semi-liquid materials - from wall paints to thin plaster compounds - and stores neatly via its rubber hanging hole when the job is done.