Skip to Content
Shopping Basket
Your basket is empty.

Everbuild Lumberjack 160 Wood Flooring Adhesive LJACK16010

Ref: QR28521
Everbuild Lumberjack 160 Wood Flooring Adhesive LJACK16010
£78.61
£94.33 inc. VAT
NOW £40.88
£49.05 inc. VAT
In Stock

Purchase

Total Discount Price:

? x Everbuild Lumberjack 160 Wood Flooring Adhesive LJACK16010:
£49.05
 
£40.88 ex VAT
Select Quantity and choose Add To Basket

Description

Everbuild Lumberjack 160 Wood Flooring Adhesive LJACK16010

 

 

 

Everbuild Lumberjack 160 Wood Flooring Adhesive LJACK16010

 

Everbuild Lumberjack 160 Wood Flooring Adhesive 10 Litre

Barcode: 5029347609665

MPN: LJACK16010

Description:

LUMBERJACK 160 high specification, trowel applied wood flooring adhesive based on a resin and solvent blend,

Specifically designed for fixing all types of wooden floors directly onto porous substrates.

 

Lumberjack 160 Benefits:

Water free will not cause warpage or curl of wood blocks and planks.

Rapid Setting, Floors may normally be trafficked 12-24 hours after application.

Will bond wood directly to all common porous subfloors including concrete, wood and porous natural stone floors.

Easy application by trowel.

High strength adhesive.

Suitable for use with underfloor heating.

 

Product Limitations:

SOLVENT BASED PRODUCTS ARE FLAMMABLE.

Keep away from sources of ignition.

Avoid inhalation of fumes and ensure good ventilation during use and after fixing until product is dry. In confined spaces use forced ventilation.

If any of the above are an issue use lumberjack 650 flooring adhesive.

Do not use against bitumen or substrates that bleed oil or plasticizers.

This product is only suitable for direct applications to subfloors where humidity level is below 2.5%. For applications where humidity level is between 2.5 and 7%, always use Lumberjack M.B Primer and screed over as directed. Never apply wooden flooring under any circumstances where humidity level is above 7% check with a moisture detector.


Surface Preparation:

The surfaces to be glued must be porous, sound, clean, dry and free from dust, grease and other contaminants. 

Existing floors and chipboard must be free from all polish and wax. 

New concrete must be allowed 4 weeks to dry and mature.

Always check moisture level of subfloor.

 

Moist Floors:

If moisture levels in subfloor are above those recommended by the flooring manufacturer, damp proof the floor with at least two coats of Lumberjack M.B Primer as directed.

then prime with EVERBUILD 501 PVA BOND diluted 1:3 PVA: to water and screed with a minimum 3mm depth EVERBUILD SELF LEVEL FLEXI PLUS whilst primer is tacky.

 

Under floor heating:

underfloor heating must be turned off 48 hours before and 48 hours after the adhesive has been applied.

 

Non Porous Surfaces:

Not suitable for direct application. Prime 1:3 to water: EVERBUILD PVA BOND and screed with a minimum 3mm depth of EVERBUILD SELF LEVEL FLEXIPLUS whilst primer is tacky.  Allow to cure for 24 hours or until dry, whichever is longer then proceed as per porous surfaces.

 

Flooring:

The wood flooring MUST be acclimatised for several days in the room where it is to be installed. Leave in original packaging during this period.

 

Application:

Open bucket and trowel onto floor.

Spread evenly with a suitable notched trowel at no less than 0.5kg/m² to 1.0Kg/.

Do not spread more adhesive than can be covered within 10 to 15 minutes 1m² maximum.

Place planks or blocks into position whilst adhesive is still tacky within 10 minutes tap into final position with mallet and block,

Remove uncured adhesive with Wonder Wipes caution - test compatibility with lacquer finished blocks wipes and adhesive first.

Floor may be sanded and trafficked 12-24 hours after application, depending on site conditions (longer at low temperatures). 

If subfloor has poor absorbency; allow 3 days before sanding and trafficking

For full surface bonding only. Ensure that the contact faces of the wood elements are fully wetted with adhesive.

 

Coverage:

0.5 to 1.0 kg Liter per m2 depending upon size of notched trowel used and subfloor surface profile.

For the bonding of long or wide boards or in case of uneven substrates it could be necessary to use a notched trowel with bigger notches avoid hollow sections.

 

See All Wood Floor Adhesives

Extensions

default
Reference Code:
LJACK16010
Option Text:
10 kg 10 liter